New Buck Corporation 34 Bedienungsanleitung

MODEL 34 MAY BE INSTALLED IN A SOLID FUEL BURNING FIREPLACE, AS A ZERO CLEARANCE FIREPLACE OR WITH AN OPTIONAL SURROUND. WAR N I N G: If the informat

CR3329 CERAMIC LOG SET PLACEMENT, FOR MODEL 34 (1-L) (2) (4) (3) WARNING: Failure to position the parts in accordance with these diagra

EMBER STOVE LOG SET PLACEMENT FOR MODEL 34 MODEL E.S.B: 1)Rear Log, 2)Middle Log, 3)Left Top Middle Log, 4)Right Top Middle Log 5)Left Fro

GAS PRESSURE CHECK Check the inlet pressure to the burner to ensure that it is as shown in the table below. NOTE: The pressure check point is located

LIGHTING INSTRUCTIONS MILLIVOLT VALVE (ITT) FOR YOUR SAFETY, READ BEFORE LIGHTING WARNING IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE O

LIGHTING INSTRUCTIONS 1. STOP! Read the safety information on previous page. 2. Make sure the manual shutoff valve is fully closed.If equipped wi

• If the pilot will not stay lit after several tries, turn the gas control knob to “OFF” and call your service technician or gas supplier. TO TURN O

THERMOSTAT CONTROL OPERATION • This valve operates off of millivolts produced by the generator. You may choose to use an optional Wall Thermostat o

LIGHTING INSTRUCTION MODULATING VALVE (SIT) MANUAL VALVE (SIT) FOR YOUR SAFETY READ BEFORE LIGHTING WARNING IF YOU DO NOT FOLLOW T

LIGHTING INSTRUCTION 1. STOP! Read the safety information on preceding page 15. 2. Make sure manual shutoff valve is fully closed. 3. Turn off a

11. Turn gas control knob counterclockwise to “ON” position. Continue to turn the gas control knob counterclockwise

THERMOSTAT CONTROL OPERATION 1. The thermostat control on this heater differs from standard thermostats. Standard thermostats simply turn the burne

OPERATING INSTRUCTIONS Before operating this appliance, proceed through the following checklist. 1. Read and understand these instructions before o

REMOTE CONTROL OR WALL THERMOSTAT NOTE: Knob cannot be turned from “PILOT” to “OFF” unless knob is pushed in slightly. Do not force. 6. Wait (5)

* If the pilot will not stay lit after several tries, turn the gas control knob to “OFF” and call your service technician or gas supplier. 11. Turn c

MANUAL LIGHTING PROCEDURE 1. If the pilot cannot be lit with the piezo, it can be manually lit with the use of a paper match and a lighter rod. 2.

FLAME CHECK A periodic check of the flames should be made. The pilot flame should always be present when the gas logs are in operation. See Figure

WIRING DIAGRAM NOTE: “If any of the original wire as supplied with the gas appliance must be replaced, it must be replaced with a wire of at least a 1

WARNING: ELECTRICAL GROUNDING INSTRUCTION: THIS HEATER IS EQUIPPED WITH A THREE-PRONG PLUG FOR YOUR PROTECTION AGAINST SHOCK HAZARD AND SHOULD BE PLU

SECTION III INSTALLATION MODEL 34 (FP) IN SOLID FUEL BURNING FIREPLACES (1) The Model FP-34 may be installed in a masonry fireplace. The minimum fire

B. Set the top (long) trim panel in place on top of unit. The panel should be flat against the outside face of the fireplace, and standing vertical

TABLE OF CONTENTS MODEL 34 SECTION I: Safety Information... 3 SE

SECTION IV INSTALLATION OF MODEL 34 (WS) OPTIONAL WOODEN SURROUND (KIT#PAKDFP34) NOTE: See page 26, figure 6 for clearances. (1) When choosing the

STEP 7: Slide the unit into the front opening of the surround so the top metal trim panel and outer sides of the heater meet flush with the surround

SECTION V MODEL 34 (ZC) ZERO CLEARANCE INSTALLATION The installation must conform with local codes ,or in the absence of local codes, with the

3-1/4"4-1/4"GAS LINE WARNING: Installation and repairs should be performed by a qualified service person. The appliance should be inspec

FIREPLACE CLEARANCES (ZC) The fireplace may be placed directly on a combustible floor, against a combustible wall at marked clear-ances, or on a rai

FINISHING YOUR FIREPLACE (ZC) There is a wide variety of finishing material available for your fireplace from formal wall treatments with marble and

SECTION VI AFTER MARKET MOBILE HOME INSTALLATION NOTE: See “Producing Adequate Ventilation” page 35 .THIS APPLIANCE MAY BE INSTALLED IN AN AFTERMAR

PRODUCING ADEQUATE VENTILATION This section is for residential or manufactured (mobile) installation “This heater shall not be installed in a confine

1. Determine the volume of the space (length x width x height). Length x Width x Height =_________cu.ft.(volume of space) EX

VENTILATION AIR VENTILATION AIR FROM INSIDE BUILDING This fresh air would come from an adjoining unconfined space. When venting to an adjoining spa

VENTILATION AIR FROM OUTDOORS Provide extra fresh air by using ventilation grills or ducts. You must provide two permanent openings: one within 12&q

IMPORTANT SAFEGUARDS Although your gas logs are very realistic in appearance, it is not a real burning fireplace and must not be used for burning rej

TROUBLESHOOTING WARNING TURN OFF, UNPLUG HEATER AND LET COOL BEFORE SERVICING. ONLY A QUALIFIED SERVICE PERSON SHOULD SERVICE AND REPAIR HEATER. CAU

OBSERVED PROBLEM ODS/PILOT lights but flame goes out when control knob is released 4. Air in gas lines when installed 5. Depleted gas

OBSERVED PROBLEM Burner does not light after ODS/Pilot is lit Delayed ignition of burner Burner backfiring during combustion Slight smok

WARNING IF YOU SMELL GAS: * SHUT OFF GAS SUPPLY * DO NOT TRY TO LIGHT APPLIANCE * DO NOT TOUCH ANY ELECTRICAL SWITCH; DO NOT USE ANY

SERVICING Repair and replacement work should only be performed by a qualified service technician. Always shut off the gas supply and make sure heate

REPLACEMENT PARTS ITT VALVE (Picture on page 46) KEY# PART DESCRIPTION PART NUMBER 1. Carling Switch PE RA911VB 2. Female Terminals PE

ON123467892013171619125111415181021THERMOGENAUXPRESS TORESETOFFPILOTONITTGENERALCONTROLSPILOTADJ 46

REPLACEMENT PARTS SIT MODULATING OR MANUAL VALVE (Picture on page 48) KEY# PART DESCRIPTION PART NUMBER 1. Pilot (NAT.) Copreci PE 2150053

SECTION I SAFETY INFORMATION WARNINGS IMPORTANT: READ THIS OWNER’S MANUAL CAREFULLY AND COMPLETELY BEFORE TRYING TO A

10PILOTOFFHILOSit9123A16183B475861213111217151419 48

REPLACEMENT PARTS SIT MILLIVOLT VALVE Picture on Page 50 KEY#

SIT MILLIVOLT 15 8 16 2 4 5 3 7 1 6 17 18 19 9 10 11 13 12 14 20 21 50

REPLACEMENT PARTS FOR EMBER STOVE BASE (ESB) (PICTURE ON PAGE 47) A parts list with exploded view follows. Always include correct name, part number,

52 10 6 11 13 8 7 16 16 5 1 14 2 3 4 6 17 15 12 REPAIR PARTS A parts list with exploded view follows. Always include correct name, part

NEW BUCK CORPORATION We reserve the right to amend these specifications at any time without notice. The only warranty applicable is our standard wri

5. If this heater is used with propane gas, do not place propane supply tank (s) inside any structure. 6. What To Do IF You Smell Gas: Shu

21. All heater screens must be kept closed when operating the gas logs. 22. ”WARNING: Failure to keep the primary air opening (s) of the burner (s)

SECTION II FIREPLACE PREPARATION The fireplace needs to be prepared before installing the heater. A. Turn off the gas supply to the fireplace.

INSTALLATION AND CLEARANCES To ensure a safe installation into a masonry or factory built fireplace, the following instructions must be carefully fol