NEW BUCK CORPORATION MODEL 1110 VENT-FREE GAS HEATER WAR N I N G: If the information in this manual is not followed exactly, a fire or explosion may
CAUTION THIS HEATER CREATES WARM AIR CURRENTS. THESE CURRENTS MOVE HEAT TO WALL SURFACES NEXT TO HEATER. DO NOT INSTALL HEATER WHERE IMPURITIES IN T
INSTALLATION NOTE: This heater may be installed three different ways: 1. Wall Mounted 2. Freestanding heater (with optional pedestal) 3. Freest
3. Lift heater by each bottom corner and place the round part of the tear drop punch out over each screw head. Gently push down until the body of t
FREESTANDING WITH OPTIONAL PEDESTAL INSTALLATION 1. Place heater on backside and center the pedestal on the bottom. Mark the 4 pre-punched holes in
MOUNTING BRACKET VIEW FREE-STANDING OPTIONAL DELUXE FINISHED MANTEL Figure 7 DATEREV.BDATEREAR OF MANTEL REAR OF STOVE Z BRACKETS REAR OF STOVE Z-BRA
PRODUCING ADEQUATE VENTILATION This section is for residential or manufactured (mobile) installation “This heater shall not be installed in a confine
1. Determine the volume of the space (length x width x height). Length x Width x Height =_________cu.ft.(volume of space) EX
VENTILATION AIR VENTILATION AIR FROM INSIDE BUILDING This fresh air would come from an adjoining unconfined space. When venting to an adjoining spac
Figure 9 VENTILATED ATTIC OUTLET AIR OUTLET AIR INLET AIR TO ATTIC TO CRAWL SPACE INLET AIR VENTILATED CRAWL SPACE VENTILATION AIR FROM OUTDOORS Pro
WAR N I N G : ANY CHANGE TO THIS HEATER OR ITS CONTROLS CAN BE DANGEROUS. GAS CONNECTION Check gas type. Use only the type of gas indicated on th
CONNECTING TO A GAS SUPPLY CAUTION: NEVER CONNECT HEATER DIRECTLY TO THE PROPANE SUPPLY. THIS HEATER REQUIRES AN EXTERNAL REGULATOR (NOT SUPPLIED
CAUTION: Use only new black iron or steel pipe. Internally tinned copper tubing may be used in certain areas. Check state and local codes. Use pi
GAS PRESSURE CHECK Check the inlet pressure to the burner to insure that it is as shown in the table below. NOTE: The pressure check point is locate
LOG PLACEMENT FOR 1110 Logs are shipped secured in unit. NOTE: When operated for the first time, logs may emit a “paper burning” smell. This smell
LIGHTING INSTRUCTIONS MODULATING VALVE(MAXITROL) FOR YOUR SAFETY, READ BEFORE LIGHTING
LIGHTING INSTRUCTIONS 1. STOP! Read the safety information on the previous page. 2. Make sure manual shutoff valv
CAUTION: Hot while in operation. Do Not Touch. Keep children, clothing, furniture, gasoline, and other liquids having flammable vapors away. CAUTIO
THERMOSTAT CONTROL OPERATION The thermostat control used on this heater differs from standard thermostats. Standard thermostats simply turn the
FLAME CHECK A periodic check of the flames should be made. The pilot flame should always be present when the gas logs are in operation. FLAME:
If burner flame pattern is incorrect, as shown in Figure 19 *turn heater OFF (see “To Turn Off Gas t
TABLE OF CONTENTS Safety Information and Warnings ... 3 Product Ident
WARNING: CHILDREN AND ADULTS SHOULD BE ALERTED TO THE HAZARDS OF HIGH SURFACE TEMPERATURE AND SHOULD STAY AWAY TO AVOID BURNS OR CLOTHING IGNITION.
WARNING: ELECTRICAL GROUNDING INSTRUCTION: THIS APPLIANCE IS EQUIPPED WITH A THREE-PRONG (GROUNDING) PLUG FOR YOUR PROTECTION AGAINST SHOCK HAZARD AN
IMPORTANT SAFEGUARDS Although your gas logs are very realistic in appearance, it is not a real burning fireplace and must not be used for burning rej
TROUBLE-SHOOTING WARNING TURN OFF AND UNPLUG HEATER AND LET COOL BEFORE SERVICING. ONLY A QUALIFIED SERVICE PERSON SHOULD SERVICE AND REPAIR HEATER.
OBSERVED PROBLEM 1. Igniter button is pressed. No spark at ODS/Pilot 2. Igniter button is pressed Spark at ODS/Pilot No Ignition POS
OBSERVED PROBLEM 3. ODS/PILOT lights but flame goes out when control knob is released 4. Burner does not light after ODS/Pi
OBSERVED PROBLEM 5. Delayed ignition of burner 6. Burner backfiring during combustion 7. Slight smoke or odor during initial operation
WARNING IF YOU SMELL GAS: * SHUT OFF GAS SUPPLY * DO NOT TRY TO LIGHT APPLIANCE * DO NOT TOUCH ANY ELECTRICAL SWITCH; DO NOT USE ANY
TECHNICAL SERVICE MODEL 1110 MODULATING VALVE BTU. 10,000 10,000 Type Gas Propane (LP) Natural Ignitio
PARTS LIST KEY NO. PART NUMBER DESCRIPTION QUANTITY 1 MF 112738 VENT ROD 3 2 PO 1127IM BRASS TRIM 4 3 PO PNPSNH50JT FRONT
2
BLOWN UP VIEW OF HEATER, FAN MOTOR, AND ALL REMOVABLE PARTS 38
PARTS LIST Maxitrol Valve KEY # PART # DESCRIPTION QUANTITY 1 GV 30B5A2L7B Maxitrol LP Valve 1 1A GV 30B5A2N7B Maxitrol Nat. Valve
BLOWN UP VIEW OF BURNER ASSEMBLY 40
NEW BUCK CORPORATION We reserve the right to amend these specifications at any time without notice. The only warranty applicable is our standard wri
SAFETY INFORMATION WAR N I N GS IMPORTANT: READ THIS OWNER’S MANUAL CAREFULLY AND COMPLETELY BEFORE TRYING TO ASSEMBLE, OPERATE, OR SERVICE THIS APP
5. If this heater is used with propane gas, do not place propane supply tank (s) inside any structure. 6. What To Do IF You Smell Gas: Shu
21. All heater screens must be kept clean when operating the gas logs. 22. ”WARNING: Failure to keep the primary air opening(s) of the burner(s) cle
PRODUCT IDENTIFICATION Figure 1 WARNING:Installation and repairs should be performed by a qualified service person. The appliance should be inspecte
PRODUCT FEATURES SAFETY DEVICE This heater has a pilot with an Oxygen Depletion Sensor Shutoff System (ODS). The ODS/pilot is a required feature for
Kommentare zu diesen Handbüchern